All Products Painted Blacktical
This Allows:

* Targets that reset after impact.

* Rifle Shooting or an inexpensive "Plate Rack" for Pistol.

* Multiple Hanging Targets.

* Use with any of the Single-Hole Targets.

* Easy to Transport and Setup with a small Storage Footprint.

* Made in the USA.
"Rifleman Training Targets"...  "Because Riflemen Persist"!  Let Freedom Ring!!!
Copyright ©2013-2017 Rifleman Training Targets.  All Rights Reserved
"Target Hanger System"
Description:

"Target Hanger System" (THS) includes all the necessary Hardware you need to hang any of our single-hole Targets including the "Army Qualification Test Target", "IDPA / USPSA Silhouette", "Morgan's Shingle" and "Round" Targets with the use of the "Modular Target Stand" or the "T-Post Modular Target Bracket".  The "THS" allows Targets to naturally reset after impact due the rigid but flexible "Shoot Through" Target Hanger Strap.  You will receive two (2) Grade 8 Bolts, two (2) Nylon Lock Nuts, two (2) Washers, two (2) Target Collars, one (1) Target Hanger and one (1) "Shoot Through" Target Hanger Strap.



Directions for Assembling the "Target Hanger System":

To assemble take the "Shoot Through" Target Hanger Strap and position it behind the Target  Insert the Grade 8 Bolt through the front of the Target and put the Washer and Nut on the Back Side of the Target Hanger Strap.  Then place the Target Hanger Strap in Front of the Target Hanger and insert the Bolt into the Washer and through the Front of the Shoot Through Strap and fasten the Nut on in the Rear (see Pictures Above).  Snug all the Hardware, but do not over tighten.  Additional 9/16-inch Holes can be Drilled in the "Shoot Through" Target Hanger Strap to Raise Targets as desired.

Once you have the "THS" fully assembled slide it onto the Rebar horizontal member of the "Modular Target Stand" or the "T-Post Modular Target Bracket" with a "Target Collar" on each side of it to keep it in place, this will allow you to space and hang multiple Targets (pending overall weight of Targets). 

When using the Target Collars use "Blue" LOCTITE or equivalent on the set screws prior to tightening.


The "Target Hanger System" is Easy to Transport and Setup with a small Storage Footprint. 

Made in the USA!  Designed and Built to last by Riflemen!
The "Target Hanger System" is used to with our "Army Qualification Test", "IDPA / USPSA Silhouette", "Morgan's Shingle" and "Round" Targets to hang from the "Modular Target Stand" or the "T-Post Modular Target Bracket".  It allows Multiple Targets next to each other for a Variety of shooting Scenarios resulting in a Fun time shooting for the New and Experienced shooter.  For shooting with a Rifle or use as an inexpensive "Plate Rack" for Pistol.
Click on Images to Enlarge
Target Hanger System (1 lbs.)      $13.50
Instructions included with all products.
Requires:  Targets!!!!!!
Additional "Shoot Through" Straps $4.00
Important:  Maintain a Minimum Distance of 100-yards with a Center Fire Rifle and 15-yards with a Pistol NO CLOSER!

Do Not shoot steel with projectiles with a speed greater the 3100fps at the muzzle, no matter the caliber.

NEVER Shoot Targets with "Steel Core" or "Armor Penetrating" Rounds.

Following these guidelines will make your Target last a long time. 

Rifleman Training Targets is Not Responsible for Improperly Used Targets.

Purchaser Assumes ALL Risk and Responsibility for Any and All Accidents
.

Safe Shooting is No Accident
!!  WEAR APPROPRIATE SAFETY GEAR.
Over 50 different available Targets!
Developing the "Flash Gong"!!
Back
Next

Targets for all of the Shooting Sports!

 
Rifleman Training Targets